Your Search: "pnw"

Mount your tail light to the reflector tab on the back of a rear cargo rack with this Rack Bracket from Portland Design Works. - Compatible with all PDW rear lights except the Asteroid and Fenderbot - Horizontal holes are 50mm apart to fit European rack standards - Vertical holes are 18mm apart to fit most reflector mounts

Add a little flair and extra visibility to your ride. A Saddle Charm adds character to the tail of your whip! Made of our woven handlebar tape, a sturdy thread locking loop, and highly reflective 3M trim, our Saddle Charms can be attached to the rails of your saddle, the bag loops on a Brooks England saddle, or just about anywhere on your bike or bag for a pop of added safety and fun. They may even give you a bit of extra luck.

It's always a good idea to have backup hardware. This is a replacement hardware pack for Portland Design Works Payload or Loading Dock rear racks. - 2x P clamps - 4x nyloc nuts - 4x hex bolts

Portland Design Works' 16 ounce Co2 Cartridges are threaded, work with most Co2 inflators that require threaded cartridges, and are food-grade so they're completely gentle and safe for your valves and tubes.

Every commuter bike needs a good bell, and this is it: It's a Brass Bell. It's small, it's loud, it's not ostentatious, It's a Brass Bell. Greet your friends, alert pedestrians, put a ring on it! - Fits 22.2mm handlebars

These clip-on fenders are designed specifically for fat bikes. They're extra long and wide to block the muck, snow, or sand you'll ride through on your next fat bike adventure. - Extra-long and wide to accommodate the biggest tires - Easy to install and fits virtually any bicycle - Works with both rigid and suspension forks

The PDW Outpost Mount allows you to attach a handlebar-mounted headlight to the side of your tapered wire basket—eliminating the problem of basket cargo blocking the light beam. The attachment plate compensates for the angle of a tapered wire basket, allowing the headlight to stay nice and level. - 32mm diameter clamping area for lights - Attaches with two M5 bolts and a steel backing plate - Mounts on left or right side

Just the thing for rainy weather, the Portland Design Works minimalist Origami Front Fender attaches to a snap-on/off bracket you mount on your downtube. And it folds flat so you can easily stow it when not in use. - Length: 370mm (14.5") - Weight: 60g (2.1oz)

Portland Design Works has given the original fat bike front fender a facelift! The Mud Shovel 6.5 Front Fender was designed specifically for fat bikes - they're extra long and wide to block the muck, snow, or sand you'll ride through on your next fat bike adventure. Made of heavy-duty polymer, the Mud Shovel 6.5 Front Fender is super lightweight but sturdy enough to take years of bad weather abuse. The fender mounts to the downtube of your bike using adjustable rubber straps for a secure fit. - Front fender is 254mm wide and 622mm long (10" x 24.5") - Extra-long, wide design blocks snow, water and sand - Bracket keeps fender super stable and is easy to install - Built with lightweight, sturdy materials for durability

The Fatty Object CO2 inflator fits on both Presta and Schrader valves and its oversized control knob is easy to operate, even with gloves on. - Precision machined alloy parts - For use with both Presta and Schrader valves

Portland Design Works' Shiny Object is made from aluminum for strength and low weight so you won't think twice about bringing this ride essential along with you. A control knob keeps you in charge of the pressure, it takes threaded Co2 cartridges (sold separately) and it fits both Presta and Schrader valves. - Inflator only height: 44 mm (1.75") - Inflator only weight: 40 g (1.5 oz) 

Put on the high beams for extra visibility even in the dark corners of space. Portland Design Works' Spaceship Headlight boasts 3 bright LEDs which shine through a precision lens for a bright, focused beam. It offers steady and flashing modes and has a run time of over 100 hours. - Fits 22.0-31.8mm handlebars - Runs on 2 x AA batteries (included) - 100 hours run time - Steady and flashing modes - 91 grams/3.2 ounces - 98 x 41 x 35mm

Just the thing for rainy weather, the Portland Design Works minimalist Origami Rear Seatpost Fender attaches to a clamp-on bracket you mount to your seatpost. And it packs down so you can easily store it when not in use. - Length: 445mm (7.5") - Weight: 160g (5.6oz)

Portland Design Works' neat Sodapop Fenders are made from 97% post-consumer recycled bottles. They pop on and off with ease, keep you dry in the rain, and get one back for the planet, too! - City width: 48 mm at tail - Mountain width: 64 mm at tail

It's a CO2 inflator! Constructed of durable alloy and composite, this price-point CO2 inflator is sure to save you on the side of the road. The oversize control knob makes for easy regulation of air flow. Comes with two 16g CO2 cartridges and a foam sleeve to protect your fingers from the frosty cartridge. - Oversize control knob regulates CO2 flow - Durable composite and alloy construction - Includes 2x 16g CO2 cartridges + 1 foam sleeve - Presta and Schrader compatible

Portland Design Works' 3wrencho is a strong and versatile addition to your fixed gear, townie or workbench! Made of heat-treated steel for extra toughness, it's part tire lever, part 15mm wrench. Its strong nylon coating won't scratch rims, so you can pry as hard as you need to remove stubborn tires. Step on the 3wrencho for extra leverage to loosening axle nuts. May also be used to spread peanut butter, stir a drink, or open a letter. - Length: 114 mm (4.5") - Weight: 95 g (3.5 oz)

Portland Design Works' incredibly lightweight and compact Tiny Object CO2 Inflator efficiently fills flats. Use the control knob to dial in the perfect pressure while the included leather sleeve protects your hands from frosty CO2 cartridges. Its rugged alloy body is built to withstand years of road- and trail-side repairs. - Presta valve compatible - Control knob easily regulates CO2 flow - Full grain leather sleeve is vegetable tanned and conditioned with natural oils and waxes - Lifetime PDWarranty

Everybody knows you can't really shred without a solid power stance. The Power Stance kickstand is the whammy bar of kickstands. Take your city shred session to the next level when you slam down the Power Stance. WEOW WEOW! Built with e-bikes, cargo bikes, touring bikes and commuters in mind, the Power Stance is incredibly sturdy. The length is adjustable by the push of a button for quick installation and easy adjustment if parked on uneven ground. Lean easy for years to come with the ultra burly Power Stance kickstand. - Direct mount version - Burly construction is great for supporting heavy bikes - Adjust the length with the press of a button - Durable composite foot - Lifetime PDWarranty

Everybody knows you can't really shred without a solid power stance. The Power Stance kickstand is the whammy bar of kickstands. Take your city shred session to the next level when you slam down the Power Stance. WEOW WEOW! Built with e-bikes, cargo bikes, touring bikes and commuters in mind, the Power Stance is incredibly sturdy. The length is adjustable by the push of a button for quick installation and easy adjustment if parked on uneven ground. Lean easy for years to come with the ultra burly Power Stance kickstand. - Center mount version is compatible with almost any adult bicycle - Burly construction is great for supporting heavy bikes - Adjust the length with the press of a button - Durable composite foot - Lifetime PDWarranty

We can't promise to keep your hands warm as the seasons change, but we can keep your paws feeling fresh with our all-new Loam Grip. We packed this grip full of features, like an ultra tacky compound and ergonomic pattern to support your palms and help relieve any fatigue caused by trail chatter and long days in the saddle. The Loam Grip features two contrasting patterns, and these dueling motifs play an important ergonomic role. Thin strips run horizontally across the grip's surface for enhanced traction and supple feel, while the thicker mountain pattern helps support the pad of your hand. Beefing up this outer zone with a heartier design combats compound deterioration, ensures the grip is absorbing more vibration, and provides needed structure to support the additional body weight pressing down on this area. The Loam Grip was purpose-built for Enduro/Trail riding, and with that in mind, picking the compound was extremely important. We needed to identify a blend that was soft enough to absorb vibration, yet firm enough to keep its shape under pressure. We call this the "happy camper" blend because it strikes a balance between an ultra-soft material that wears too quickly and a harder compound that provides no tactile benefits. - Diameter: Avg. 30mm - Weight: 90g/pair - Width: 133.5mm - Durometer: 25A Happy Camper Compound - Clamp Style: Closed End, single clamp

Announce your presence with Portland Design Works' King Of Ding II Bell. This solid brass bell rings loud and clear. - Solid brass bell - Brass striker - Alloy mounting - Fits 22.2 - 25.4mm handlebars

These clip-on fenders are designed specifically for fat bikes. They're extra-long and wide to block the muck, snow, or sand you'll ride through on your next fat bike adventure. - Extra-long and wide to accommodate the biggest tires - Easy to install and fits virtually any bicycle

The Portland Design Works Owl Cage is made from a single sheet of lightweight 5052 alloy. Cut in the shape of a Great Horned Owl, its wings fold in to securely cradle your water bottle. Get an Owl and make your ride fly. - Constructed of 5052 alloy - Weight: 67 g (2.3 oz) - Includes two stainless bolts for installation - Lifetime PDWarranty

The Portland Design Works Sparrow Cage is made from a single sheet of lightweight 5052 alloy. The Sparrow's wings fold in to securely cradle your water bottle and the cut outs help keep the cage light. Get a Sparrow and make your ride fly. - Constructed of 5052 alloy - Includes two stainless bolts for installation  - Weight: 57g (2oz) - Lifetime PDWarranty

Portland Design Works' Fenderbot Taillight shines brightly to enhance your visibility when the sky turns dark. It boasts a 1-watt LED with three modes and precision reflector to notify others of your presence. And, the Fenderbot bolts directly to your fender so it's always on your bike. - Bright red LED and precision reflector - Bolts directly to fender to prevent theft - Weatherproof exterior for all season riding - Weight: 62 g (2.2 oz) - Runs on 2xAAA batteries (included) - Lifetime PDWarranty

Fat Paw grips were developed for riders who crave large-diameter grips that also have a soft feel. The 9.5mm grip thickness reduces hand fatigue and finger numbness, making it an ideal option for riders with large or gloved hands. - 100% proprietary dual-density silicone compound provides excellent vibration damping and conforms to your hand for improved comfort while maintaining durability - Tacky texture provides excellent grip with or without gloves in all weather conditions - Includes bar end plugs

Ergonomic grips with this unique cam profile lets you choose the position that best supports your hand position and style of riding. The 11.5mm grip thickness reduces hand fatigue and finger numbness, making it an ideal option for riders with large or gloved hands. - 40mm installed diameter - 100% proprietary dual-density silicone compound provides excellent vibration damping and conforms to your hand for improved comfort while maintaining durability - Tacky texture provides excellent grip with or without gloves in all weather conditions - Ergonomic shape makes for a reduced circumference compared to non-faceted grips, providing padding and comfort only where you need it - Facets create four edges on grips, which makes for additional points of contact for your hands and added grip - Includes bar end plugs

Announce your presence with Portland Design Works' Alexander Graham Bell. Built to replace a 10mm 1 1/8 headset spacer, this bell is a classy addition to your rig without sacrificing any of your precious handlebar real estate. - Polished brass bell  - Replaces a 10mm 1 1/8" headset spacer - Quick-reflex alloy clapper - Lifetime PDWarranty

The PDW Hot Take cup holder is adjustable to hold most any size of travel thermos. Its soft design will keep hot or cold liquids at arm's length, secure and rattle-free.

Coming in hot! This limited edition King of Ding II is laser-engraved "COMING IN HOT." Perfect for speed demons, messengers, cat6 champions, and anyone else who "can't stop, don't want to." The bell is made of solid brass and comes equipped with a brass striker for a loud clear ring that's sure to clear the path. The alloy mount is easy to install and fits 22.2 – 25.4mm handlebars.